SHARI PiZero

Overview

The SHARI (SA818 Ham Allstar Radio Interface) PiZero Allstar Node is a kit construction project that implements a Raspberry PiZero 2W (must be the 2W) hosted Allstar node using a NiceRF SA818 embedded UHF (420 – 450 MHz) or a VHF (144-148 MHz) radio module. Three USB ports with microB connectors are provided by a USB hub on the PiZero PC board. This permits the node owner to utilize wired ethernet connection to the node using a microB USB to ethernet dongle cable. Power is provided to the node using a suitable Raspberry PiZero power supply (microB connector)

SHARI PiZero (UHF Model)

The VHF or UHF radio module, interface circuits and the USB hub for the PiZero are located on a custom printed circuit board using surface mount components. The Raspberry PiZero 2W plugs into the PC board via its 40 pin GPIO connector and a custom USB adapter cable.

SHARI PiZero Motherboard with PiZero Daughterboard

Features

  • Uses a CMedia CM108B or CM119B USB Audio IC.
  • Uses a NiceRF SA818S UHF (420-450 MHZ) or VHF (144-148MHz) embedded radio module
  • LTCC lowpass output filter ensures compliance with Part 97 spurious requirements
  • 300 to 500 milliwatts RF output power.
  • Three microB USB ports to plug in USB devices such as an external ethernet adapter for a wired ethernet connection or an external keyboard.
  • Hammond extruded aluminum metal enclosure (approximately 3.25 x 2.25 x 1 inch).
  • RX/TX serial connection from the PiZero GPIO to the SA-818 radio module to program RF module parameters including RF frequency and CTCSS/CDCSS codes.
  • Clamp-on ferrite provided to mitigate buzz interference from high RF fields near the Pi power supply.
  • Raspberry PiZero 2W, power supply and microSD card provided by kit builder.

Construction and Setup

The SHARI PiZero kit parts are shown in the next photo. The kit builder supplies the PiZero 2W (must be a 2W with no installed pin header) and a PiZero power supply.

SHARI PiZero Kit Parts (blank end plates not shown)

The SHARI PiZero PC board is supplied with all the small surface mount parts installed. The kit builder installs two through-hole connectors, an SMA RF connector and the SA818 radio module. The builder also installs two pin header connectors in the PiZero. A pre-built cable is supplied to connect the PiZero to the SHARI PiZero motherboard. 3D printed end caps are provided as well as blank end plates that the builder can modify with the required holes (if desired).

Detailed construction and setup documents are provided with the kit. A builder supplied microUSB to Ethernet adapter cable is recommended for setup.

Ordering Information

SHARI PiZero is designed as a kit for construction and use in the amateur radio service by licensed amateur radio operators who can assure that the SHARI PiHat kit they are using meets required operating requirements including frequency, bandwidth and required power levels at the fundamental and harmonic frequencies. There are two SHARI PiZero kits:

SHARI PihatU (UHF-70cm, 420-450 MHz)
SHARI PiHatV (VHF-2 meters, 144-148 MHz)

SHARI PiZero is available as a parts kit for, $80 (UHF and VHF). You supply the Raspberry PiZero 2W, PiZero power supply and microSD card . Please be sure to request and study the SHARI PiZero construction manual to be sure you own the required tools and possess the required mechanical and soldering skills to build the kit. We will solder the SA818 radio module onto the PCB for an additional $5.

We can also build the kit for you using a Raspberry PiZero 2W that you procure and send (or have drop shipped) to us. We will completely assemble and test the kit but you must still procure a the PiZero power supply, a microSD card, download the image and perform the setup of your node. A fully assembled and tested SHARI PiHat kit with you supplying the PiZero 2W and PiZero power supply per the above paragraph is $135 (UHF and VHF).

If you want us to supply the PiZero 2W and power supply also, then an assembled PiZeroU or PiZeroV is $205. This option is currently unavailable due to non-availability of the PiZero 2W.

Shipping to US destinations is $9 via USPS Priority Mail provided your order fits in our standard shipping box. Payment via Paypal is preferred.

Send an email including your amateur radio call indicating the SHARI PiZero model and type (kit or assembled) you would like to purchase to kitsforhams@gmail.com for construction and setup manuals, ordering and delivery information. After we determine the exact model and options you desire, we will send you a customized Paypal invoice for payment.

Comments are closed.